Digital converters

Digital converters

by adminCategories ProductNo Comments

Driver 24 watt series model L24W-BS
(LOMINEX24W-BARE BOARD SERIAL)
Driver 24 watt series L24W-BS D model (LOMINEX24W-BARE BOARD SERIAL)
A Brief Overview of Digital Transformers
This type of driver is used to set up lamps consisting of power LEDs such as RGB wallpapers, RGB projectors, RGB burials and other similar products
Each driver is designed from 3 channels (R-G-B) with programmability
The existing driver is a function of the standard DMX 512 protocol and can only be launched with DMX 512 series controllers
It is programmable with the ability to connect to the controller device, and also if not connected to the controller, it is able to play a number of effects by default from the internal memory of the IC without the need to connect to the controller
Technical parameters of digital converters
Board size: 48L × ۲۶W) MM)
Input voltage: DC (12V ~ 30V) V
Output current per line: 300MA 5.5%
Output power of each line: (1-6) W
Maximum power consumption: up to 20 watts
GRAY SCALE: 256
Connection mode: in series
Transfer protocol: DMX-512
Transfer mode: RS-485
Maximum distance between the two drivers: If you use a cable with excellent quality 100 meters
Address mode: programmable and connect to the controller
Controller: DMX-512 controller
workplace
Device performance at temperature: – 30 ° C ~ 45. C
Driver weight: 10 grams
Moisture tolerance: 5%
This controller is able to set up the following ICs
TM1803 / TM1809 / TM1804 / TM1812 / ……
UCS1903 / UCS1909 / UCS1912 / UCS2903 / 2909/2912 / ……
WS2811, BS0825 / BS0901 / BS0902 / ……
J69 / J08 / F16 / J12 / J68 / F01 / ……
D63 / D06 / D08 / D16 / D12 / D01 / ……
Programmable with LOMINEX LED PLAYER software and save the output file on SD card
Play effects manually and automatically
Multiple controllers can be synchronized through the city’s power frequency
Input voltage V B 220
FEATURE & PROTECTION protection feature
Has reverse connection protector
You have a short circuit protection for the input and output of the signal
You have a protector to prevent the driver from overheating
Voltage supply sources
To achieve the desired result, use high quality switching power, the input voltage of the driver is selected according to the lamp. See the voltage source table for more information
If you use 24-watt and 21-watt bulbs, seek the help of a technician to test and install it
If you use 9-watt, 6-watt, and 3-watt power lamps, and have to use a 12-volt power supply, be sure to check your circuit before use to avoid light loss. Because this depends directly on the power LED used in the lamp and the voltage of each LED
Our recommendation is to pay attention to the above table
Transfer distance
Distance between drivers: If you use high quality wire such as RG 45 with low resistance up to 100 meters, you can remove the controller from the first lamp or two drivers without worrying about noise
Between the driver and the LED lamp: The shorter the distance, in fact, the higher the current stability
How to connect
PCB-LED output terminal: which is in the form of VCC R G B + from the board of the LED lamp to its similar place, VCC R G +, is connected to the board of the driver by wire
Input signal: Connect A B GND from the controller terminal of the AI ​​BI GND to the board of the DMX512 driver, and also connect the output signal of the previous module to AO, BO and GND with the 3-core wire to the GND AI BI of the next DMX512 board, respectively. Connect
Connection diagram
Manual SELF-CHECK review
To check the signal in this way, connect the driver to the lamp without being connected to the main control signal. When the device is turned on, 7 colors change over time
Connection by main controller (MAIN CONTROLLER
When the lamps are connected to the main controller, they will be under control
Attention
When the power is on, avoid working and wiring the drivers separately as this will damage the driver board

Leave a Reply

Your email address will not be published.



Back to Top
Open chat
تماس با ما